Planetary Reducer Gearmotor Replacement of Rossi R2e200 R2e201 R2e240 R2e241 R2e280 R2e355 R2e428 R2e429 R2e445 R2e446 R2e542 R2e543 R2e695 R2e696

Product Description

Planetary Reducer Gearmotor Replacement Of Rossi R2E200 R2E201 R2E240 R2E241 R2E280 R2E355 R2E428 R2E429 R2E445 R2E446 R2E542 R2E543 R2E695 R2E696

Product Description

 

 

Features Of Heavy Duty Planetary Reducer Gearmotor
*Multilevel modular design
*Easy customization
*Modular add ons
*Ground gear (bevel gear and planetary gear)
*Easy to apply to any industrial application
*Shorten maintenance cycle
*Easy to maintain
*Global product and service support
*Size - 4 sizes (1060... 3000)
*Rated torque /tn2/- from 1060000 to 3000000 n · M
*Transmission ratio / inch / -80... 1000
The models we can replace Rossi
 

ROSSI Model	Our Model	ROSSI Model	Our Model	ROSSI Model	Our Model
R2E200	EP-R2E200	R3E200	EP-R3E200	R4E200	EP-R4E200
R2E201	EP-R2E201	R3E201	EP-R3E201	R4E201	EP-R4E201
R2E240	EP-R2E240	R3E240	EP-R3E240	R4E240	EP-R4E240
R2E241	EP-R2E241	R3E241	EP-R3E241	R4E241	EP-R4E241
R2E280	EP-R2E280	R3E280	EP-R3E280	R4E280	EP-R4E280
R2E355	EP-R2E355	R3E355	EP-R3E355	R4E355	EP-R4E355
R2E428	EP-R2E428	R3E428	EP-R3E428	R4E428	EP-R4E428
R2E429	EP-R2E429	R3E429	EP-R3E429	R4E429	EP-R4E429
R2E445	EP-R2E445	R3E445	EP-R3E445	R4E445	EP-R4E445
R2E446	EP-R2E446	R3E446	EP-R3E446	R4E446	EP-R4E446
R2E542	EP-R2E542	R3E542	EP-R3E542	R4E542	EP-R4E542
R2E543	EP-R2E543	R3E543	EP-R3E543	R4E543	EP-R4E543
R2E695	EP-R2E695	R3E695	EP-R3E695	R4E695	EP-R4E695
R2E696	EP-R2E696	R3E696	EP-R3E696	R4E696	EP-R4E696

Other Types of Planetary Gearboxes
How to install the Rossi planetary reducer gear motor
* tighten and tighten the torque
Use screws and tightening torques according to the design and dimensions specified on the nameplate; At least level 10.9 is required, but in the case of heavy stress, alternating load and impact, level 12.9 is used (if m2<70% × Mn2 can use grade 8.8). Screws must be equipped with ISO 7089 washers (at least 300 HV). Carefully tighten the 12.9 screws. Over tightening will damage them.
* flange installation
Please clean and carefully install the surface before installation. In the presence of external radial load or required torque m2>=0,7 × For Mn2, it is suitable for locking adhesive.
* install the gear reducer with rotary output
For the gear reducer with rotary output (output design RSH), in order to ensure the correct operation and good power transmission between the gear reducer and the machine, the gear reducer needs a rigid connection structure to bear the radial load.
* shaft installation layout
When installing the shaft, the gear reducer must be supported axially and radially by the shaft end of the driven machine, and only the reaction force with axial movement freedom and sufficient clearance in its coupling to allow slight vibration is used to prevent rotation - always evidence - will not cause dangerous overload to the gear reducer.
* install hollow shaft with shrink disk
Carefully remove the surface of the hollow shaft and the shaft end of the driven machine to be installed. Install the shrink disc on the hollow shaft of the gear reducer. First, lubricate only the outer surface of the hollow shaft. Tighten the first three screws and place them at about 120 °. Install the gear reducer on the shaft end of the machine; Slowly insert the shaft so that air escapes. Use a force wrench to tighten gradually and evenly in a continuous sequence (without crossing), approximately rotating ¼ Circle several times until you can't reach it again ¼ Circle. Continue to apply more than 1 to 2 times and verify the bolt tightening torque. In heavy load cycles with frequent reversals, verify the bolt tightening torque again after several hours of operation.
* adjustment of meshing clearance
To adjust the meshing clearance, it is recommended to put itself in the initial minimum clearance state, which can be obtained by manufacturing the maximum eccentricity on the surface of the gear reducer:
-If it is an internal gear, it faces the center of the rack; For the outer gear, 180 ° from the center. In this case, the meshing clearance shall not be less than 0,03 ÷ 0,04 x M. It is also recommended that the measured clearance is within the range recommended by the frame manufacturer. It is recommended to use a calibrated thickness to measure the gap. Only high-quality grease suitable for high load gear lubrication can be used for pinion and rack lubrication.
How To Select a Complete planetary gearbox

We, ever power, will provide appropriate equipment and parts for your agricultural applications to ensure that your agricultural needs are met. We are proud to provide more than 6000 stock parts, so you can be sure that we will have damaged parts that need to be replaced. Whether you need a suspension pin, blade, rake, PTO shaft, pull rod, disc bearing, roller chain, carolone mower parts or spray. Even prepare a brand-new tractor seat for yourself to make yourself more comfortable in a day's work.

 

Our factory

 

Related Products